Hyundai Tiburon Forums banner

motor

  1. Need 2.7L G6BA as soon as possible!!

    Parts Wanted
    I’ve developed a nasty rod knock in my 2004 GT 6spd. It’s my daily, I am tight for both funds and time, and am looking for a motor to drop in over the weekend. I’ve looked at ordering rebuild kits, but the time expense would just be too much for where I’m at right now. If someone has a decent...
  2. Solid Motor Mounts (where to buy?)

    Tiburon General Discussion
    Hey Guys! Does anyone here know where I could find solid motor mounts? I am having a hard time finding some that are available. I am looking to throw a solid motor mount in the front/rear, and also replace the transmission mount. I can't seem to find anything, but if there is any available...
  3. WTB: external door handle, motor mounts '03 i4

    Parts Wanted
    So, my passenger side door handle broke. Car isn't factory color so id like either black, silver, or unpainted. I really only need 1 of the motor mounts replaced (I believe its the driver's side... if not it's the passenger, i'll update) Less important but im also looking for speakers (both...
  4. *Important* Spun Bearing, Engine Removal

    V6 - Naturally Aspirated
    So, I spun a bearing on the tib and now have a rod knock....... -_-................. FML. And I have not found a single thread anywhere showing a step by step or a DIY of a removal with a A/T. My buddies shop has all the resources to do it, and luckily I've found a replacement motor locally...
  5. Preferred Motor mounts?

    Tiburon General Discussion
    I've read old threads,but again they're old THREADS so everyone could possibly change and have more power,what recommended motor mounts running front and rear for a stage 0 s/c and up?:smash:
  6. 94 Mustang Motor In a 1997 Tib FX possible??

    Tiburon General Discussion
    My friend gave me a motor from his old mustang and said we'll put it in if we can make it fit! He is a machinest and has worked on his car a lot - it runs like a bat outta hell!! Anyway I am wondering folks - can I put a '94 3.8L mustang motor in my '97 Tib? :JC-thinking:
  7. Need some info on why my motor started to knock

    Tiburon General Discussion
    if anyone has any idea on why my motor started to act up please let me know. the car only has 73,000 miles and i went to change the plugs and wires and when i put it back together it started knocking. i changed the plugs back to the ones it had in it from the begging thinking it was the plugs...
  8. New Problem with Clutch Please Help! During Swap

    Transmissions
    Well I finally got a chance to work on my 03 GT over my spring break. My cousin and I pulled my motor and tranny to replace the blown motor and when we split them it had the original OEM dual mass and everything looks good on it. But on the engine I was going to put in it, has the solid flywheel...
  9. FS: Stock Sub and Amp, sunroof motor and little black box.

    Parts for Sale
    all prices are plus shipping and handling. open to trades. paypal for payment. PM me for questions. 1. sunroof motor from an 03 tiburon. part # 81631-2C001. known working. $50 plus shipping 2. Stock sub. pulled from an 05 tiburon, known working. SOLD 3. Stock amp. part #...
  10. Snow / Ice & Windshield Wipers

    Tiburon General Discussion
    Well I almost blew some money on a new wiper motor yesterday. New England got slammed by a pre-Halloween snow storm and in the morning my car was covered in snow and ice. I cleared just about everything off but apparently I missed a small chunk of ice on my windshield. I started driving and...
  11. Motor Swap - Tiburon to Tiburon

    New Member Introductions
    I have a 03 Hyundai Tiburon and Im planning on getting a newer Tib and keeping the other and rebuilding the motor. I was wondering if my 03 would easily swap into a newer 05-06. I thought it would but Ive heard that it wouldn't.
  12. New tails :)

    Tiburon General Discussion
    Just ordered my new tail lights! Link: http://cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll?ViewItem&item=190492726713&viewitem=&sspagename=STRK%3AMEWAX%3AIT And i just ordered my new rear polyurithane motor mount. Cuz my rear mm is screwed *sigh* two weeks to wait now.
  13. Bad motor mounts?

    Tiburon General Discussion
    How do i tell which motor mount is bad? I can hear a clunk when i let off hard or hit the gas hard so i'm assuming its a motor mount but which one?
  14. cyl 2 misfire

    Engine Management
    I seen a couple vehicles on here with a cyl 2 misfire. My dad says the motor has low pressure because if im parked on a slight slope my car slowly slips while its in gear. The engine reading said cyl 2 misfire and i dont know what to do... i dont have money and this car only has 130 000Km on the...
  15. Car is cutting out? Need help!

    Engine Management
    Not sure really where this post should go, but I have a 2003 alpine stage 2 super charged 2.7L V6 tib. For some reason when I stand on the gas it cuts out. Sometimes when hitting 3500 RPMS. It sort of bumps. Im not super car smart so I need some help. It is alcohol injected, has a 290cc fuel...
  16. FS: FS: sunroof motor/sunroof glass (CT)

    Parts for Sale
    2 things for sale i'd like to get rid of... 1. Sunroof motor. i bought a whole sunroof assembly from the junkyard and swapped my old motor in (mine was replaced under warranty not too long ago) bench tested fine. $60-70 seems to be the going price for these, so i'll take 45-50 for it...
  17. WTB: V6 Solid Rear Motor Mount (Press in or Complete)

    Parts Wanted
    I finally blew through my poly rear, so it's time to upgrade. I'm looking for a Rear Solid Motor Mount for the V6. I do have access to a press, so really just the insert is needed; but I won't judge if someone has a full mount available.
  18. WTB: Washer fluid sprayer motor

    Parts Wanted
    I'm looking for someone that has a working motor for the washe fluid sprayers as mine is not working. I don't want to pay full retail for one if I can do without.
  19. C-shark needs some assistance...

    Tiburon General Discussion
    UPDATE: The metal ring does need to be cut out when installing the inserts. FYI. I bought the SFR poly motor mount inserts - front and rear. I understand they are supposed to be installed using a press. My question: When I remove the existing rubber from the motor mount, do I need to cut...
  20. FS: Full part out

    Parts for Sale
    Having 2 project cars is not in my budget and my Talon is too much fun to let go so that means bye bye Tibby. I am parting out absolutely EVERYTHING I can then sending what's left to the junk yard. I will not ship the big parts but I am willing to drive up to 100 miles to meet up for larger...
Top