Search Results for ‘throttle body’

I've had some issues with my throttle body sticking, and when I tighten the screw to the butterfly valve it slowly works its way back to getting stuck. I was wondering where I could find a new throttle body, as the aftermarket support is pretty bad. I am also wondering how compatible the Genesis...

Hey guys been thinking about buying a BBTB and had a few questions 1. This one I'm looking at on sharkracing.com is 58mm, what's stock size on an 03 v6? 2. If I get this, is there anything I need to do like get a tune for it or anything or is it just plug and play type of thing? 3. Any advice...

Up for sale is a matched set of a ported and polished throttle body and intake manifold. This set is for maf/cvvt beta 2 's. Price is $375 shipped to the lower 48 contiguous states. Boxed and ready to ship. ***Use at your own risk.Race part, intended for off-road use only. ***

Reduced price! $200 shipped to the contiguous 48 for the TB and manifold. I modified an oem throttle body from a map based i4 betaII. The idea is to make it act like it had the acceleration pulley installed and flow a little more cfm. In other words, have a larger opening for airfow with a...

Ok , So I have had problems with my TPS and throttle body before from the intake bringing dirt into it and I have fixed this with buying a new TPS and cleaning the throttle body once. Recently it went out again and i got a new tps, which helped with the "bogging" out when i would try to maintain...

Hey guys I'm at a loss and need some help. I recently had a check engine light go on, so I took it in and it threw a P0171 code. After doing my homework on the code I figured that with my CAI and cat-back exhaust it was normal. So driving to work today just cruising down the highway doing the...

Ngm 70mm throttle body as-is I'm selling my ngm 70mm tb as-is do to a vac leak by the butterfly seal, this can probably be fixed by geting a new seal. The tb works fine it just idle around 1300 rpms do to the leak. Selling it for $200 shipped US. SOLD

So I just read the thread that NGM is basically done or it looks that way which makes it rough to get an upper mani and throttle body. So I think I'm going to take them to a local shop and get them ported/bored. Can anyone tell me what size the mani should be ported to and what size to bore the...

I did a tune up today (plugs, wires, air filter) on my 07 Tiburon GT. What a pita that I had to remove the throttle body and intake manifold. I reconnected everything the same way that was disconnected. When I started my car it instantly stalled. I restarted and gave it some gas to keep it...

***EDIT*** I have purchased a 60mm TB from K.spec. I will be satisfied with that. I looking to buy a NGM Tri-Flow Throttle Body or equivalent to fit a Stage 4 NGM Manifold asap. I am not certain on what Throttle Body sizes are available to an Australian buyer but from my knowledge there are...

***NOTE - ANSWERED, SEE BELOW*** Hey guys, preparing myself for a big purchase for 3 intake items from RRM for my V6 2003 Tiburon but it is going to be quite pricey, especially with the core charge of $300 per item added on top. But if I send my OEM parts I should get that refunded. However, I...

I have a check engine light on and it reads code p0444 purge control curcuit open. I know thisnhas something to do with the purge control valve but what exactly is the problem? I replaced my purge control valve 4 months ago, my old one was bad and my car didnt want to start when i got gas. Since...

Can someone tell me how to fix this problem with the p0444 engine code. Something with purge control cucuit open. I replaced the purge control valve months ago. It went bad and my car would hardly start when i filled up. It ran fine for months and its still runs fine but this light has come on 3...

I am upgrading my current spark plugs and wires (95,000 miles and last owner never changed them) to NGK Iridiums with the NGK wires. as im sure everyone knows the throttle body and upper intake manifold must be removed. i am going to be replacing the gaskets on both. from the parts ive been able...

Selling a few things: First, a J&S Safeguard, with wiring harness. Asking for $325 shipped. Second, a MAF Clamp, never installed. Asking $40 shipped. Third, I have Bosch Green Top 42lb/hr 440cc injectors (set of 6), with adapters to connect to our wiring harnesses. These have only been on the...